Client Configuration

Commands

A JSON command has the following structure: {"target": "<module>", "action": "<command>", [...additional values...]}, where <module> specifies the configuration submodule and <command> specifies what should be done.

Tunnel Commands

create Sets up basic tunnel configuration. Parameters name Tunnel Name. Required. password Password. Required. server Endpoint target IP. Optional. interfaceName Desired name of the virtual tunnel network interface. Optional. values A JSON object containing configuration parameters for the tunnel.	{"target": "tunnel", "action": "create", "name": "MyTunnel", "password: "1234", "server": "10.0.0.1", "interfaceName": "bndx0", "values": {...} }
add-server Adds a endpoint server. If multiple servers are added, the client will cycle through them until a connection has been established successfully. Parameters host IP or host of the destination server. Required. port Port of the destination server. Optional (Default: "443").	{"target": "tunnel", "action": "add-server", "host": "10.0.0.1", "port": "443" }
add-interface Adds a single interface to the tunnel. Parameters interface Name of the linux network interface. Required. name Human-readable name for the interface. Optional. preset Preset that should be applied to this interface. Optional. values Configuration values for this interface. See Tunnel Settings. Optional.	{"target": "tunnel", "action": "add-interface", "interface": "wlan0", "name": "WiFi", "preset": "mobile", "values": {"enabled": false} }
create-interfaces Creates channels for the specified interfaces using presets. Parameters interfaces a JSON object where each key is a network interface name, with the corresponding value being a preset name. Required. Instead of a preset name, an object with various interface settings can be specified, as specified in #update-interfaces	{"target": "tunnel", "action": "create-interfaces", "interfaces": { "wwan0": "mobile", "eth1": "ethernet" } }
delete Resets the complete tunnel configuration, including interfaces.	{"target": "tunnel", "action": "delete" }
enable-layer2 Adds a single interface to the tunnel. Parameters bridge The name of the network bridge that should be used. Required. tapname Name of the virtual tap interface. Optional, a dynamic name will be used when no name is supplied.	{ "target": "tunnel", "action": "enable-layer2", "bridge": "br-lan", "tapname": "bondixTap0" }
enable-proxy Enables Bonding Proxy. Parameters host Host where the bonding proxy server should listen on. port Port to be used with the bonding proxy server. interface Interface from which outgoing tcp connections should be proxied.	{ "target": "tunnel", "action": "enable-proxy", "host": "0.0.0.0", "port": "18080" }
disallow-swap Explicitly tells the linux kernel to prevent memory swapping (mlockall).	{ "target": "tunnel", "action": "disallow-swap" }
quicksetup Sets up client using a base64 encoded JSON string containing connection info. JSON must be in this format: {"t":"TUNNELNAME", "p":"TUNNELPASSWORD", "s": "SERVER"} Parameters data base64 encoded JSON string.	{"target": "tunnel", "action": "quicksetup", "data": "..." } }
set Sets tunnel properties. See Tunnel Settings. Parameters values JSON object with values to change. Required.	{"target": "tunnel", "action": "set", "values": {"maxConcurrentChannel": 2} }
set-meta Allows to add custom information that is shown on the server's tunnel status page. It has no further effect. Parameters data Flat JSON object with custom info	{ "target": "tunnel", "action": "set-meta", "data": {"location": "Test Lab", "customer": "Evil Corp"} }
set-remote Sets tunnel properties on the remote end. See Tunnel Settings. Parameters values JSON object with values to change. Required.	{"target": "tunnel", "action": "set-remote", "values": {"maxConcurrentChannel": 2} }
set-interface Sets tunnel interface properties. See Tunnel Settings. Parameters index Index of the channel. 0 for first created channel, 1 for second, etc.. values JSON object with values to change.	{"target": "tunnel", "action": "set-interface", "index": 0, "values": {"enabled": false} }
set-remote-interface Sets interface properties on the remote end. See Tunnel Settings. Parameters index Index of the channel. 0 for first created channel, 1 for second, etc.. values JSON object with values to change.	{"target": "tunnel", "action": "set-remote-interface", "index": 0, "values": {"enabled": false} }
set-preset Applies a tunnel preset. See Presets for more info. Parameters name Name of the tunnel preset. Required.	{"target": "tunnel", "action": "set-preset", "preset": "Bonding" }
set-ifname Renames the virtual network tunnel interface. Parameters name The name that the interface should be renamed to. Required.	{"target": "tunnel", "action": "set-ifname", "name": "bondix0" } }
set-cert-check Enables or disables verification of the server's SSL certificate. TODO: Which root cert dir is used when no custom root certificate is provided? Parameters enabled Enables or disables SSL certificate verification. Required.	{"target": "tunnel", "action": "set-cert-check", "enabled": true } }
set-root-ca Specifies a root certificate that can be used to verify the authenticity of the remote server. When used, SSL server verification will be automatically enabled. Parameters file location of the public root certificate file. Required.	{"target": "tunnel", "action": "set-root-ca", "file": "/etc/ssl/foobar.pub" } }
set-certificate Loads a tunnel client certificate. See Certificates for further information. Parameters cert location of the public certificate file. Required. key location of the private certificate key file. Required.	{"target": "tunnel", "action": "set-certificate", "cert": "/etc/ssl/foobar.pem" "key": "/etc/ssl/foobar.key" }
embed-certs A helper functions to embed tunnel & root certificate inside the configuration instead of an external file. Performs the same actions as set-certificate and set-root-ca combined. Parameters cert The tunnel public certificate as string. Required. key The tunnel private certificate key as string. Required. root The public root certificate for server verification. Required.	{"target": "tunnel", "action": "embed-certs", "cert": "...", "key": "...", "root": "..." }
set-root-ca Specifies a root certificate that can be used to verify the authenticity of the remote server. When used, SSL server verification will be automatically enabled. Parameters file location of the public root certificate file. Required.	{"target": "tunnel", "action": "set-root-ca", "file": "/etc/ssl/foobar.pub" } }
update-interfaces Updates interface information. If a provided interface already exists, it will be updated accordingly. If a provided interface is new, it will be created. Interfaces that have been previously defined but are not provided here will be removed. Parameters interfaces JSON Object with interfaces. Key specifies the linux WAN interface to be used (e.g. "eth1"), with its value being an object with the following properties. Object Parameters name string; Interface name that is shown in logs and in the endpoint webinterface. preset string; Interface preset to be used (e.g. "mobileAggressive", "ethernet",...} upstream object; {"min": 0, "max": 100}. "min" and "max" specfiy lower and upper bandwidth limits in MBit/sec for outgoing traffic (towards endpoint). A value of "0" means no limit. When a minimum value is specified, make sure that the value is below the maximum throughput of the interface to avoid congestion. downstream object; {"min": 0, "max": 100}. "min" and "max" specfiy lower and upper bandwidth limits in MBit/sec for incoming traffic (from endpoint). A value of "0" means no limit. When a minimum value is specified, make sure that the value is below the maximum throughput of the interface to avoid congestion. standby boolean; When enabled, the interface will go into standby if other sufficient interfaces are available, as specified by the "minimum connected channel" value configured. When in standby, Bondix will make no traffic through this interface until reactivated (e.g. due to a different interface going down). You can change the minimum number of connected channel by adding this command in saneclient.json: {"target": "tunnel", "action": "set", "values": { "minConnectedChannel": 2 }} maxLatency number; overrides the maximum latency setting in milliseconds. Any packet exceeding this latency limit will be considered as lost, and the interface will not be used until latency is below the specified maximum. We do not encourage exposing this setting as it can have a negative impact on performance/throughput. (Default value is 1000 ms; enabled boolean; If disabled, the interface will not be used, but still shown in the webinterface. Note: Updating the preset will override upstream, downstream, maxLatency & standby settings to default values.	{ "target": "tunnel", "action": "update-interfaces", "interfaces": { "eth1": { "name":"WAN1", "preset": "mobileAggressive", "upstream": {"min": 0, "max": 50}, "downstream": {"min": 0, "max": 100}, "standby": false, "maxLatency": 1000, "enabled": true }, "eth2": { "name":"WAN2", "preset": "mobileAggressive", "upstream": {"min": 0, "max": 50}, "downstream": {"min": 50, "max": 100} } }
update-packetSize Updates the maximum size that UDP packets may carry. Changing this value will cause a tunnel restart. Parameters value Packet size value. Required. Valid range: 500 to 1400.	{ "target": "tunnel", "action": "update-packetSize", "value": 1400 }
cloudlink Instructs the client to use Unwired® Cloudlink to retrieve its tunnel configuration. The client will use the provided API key and the mac address of the specified interface to authenticate itself. A CA file must be provided in order to properly validate the SSL certificate of the CloudLink API endpoint. This command should not be used in combination with "create" to configure tunnel credentials or "add-server" to configure a target server. Parameters apiKey The CloudLink API key used for authentication. This key can be obtained by registering at https://admin.wifi.unwired.at interface The name of a linux interface whose mac address should be used for identification. Required. caFile Location of a root certificate used for SSL validation of the CloudLink API endpoint.	{ "target": "tunnel", "action": "cloudlink", "apiKey": "CLOUDLINK-API-KEY", "interface": "eth0", "caFile": "/etc/ssl/certs/ca-certificates.crt" }

Interactive Commands

Interactive commands can be used to interact with the tunnel and retrieve various information via the CLI socket. TODO: Add JSON responses

get Returns all tunnel settings.	{"target": "tunnel", "action": "get" }
get-interface Returns settings for a specific interface. Parameters index Index of the interface to fetch information from.	{"target": "tunnel", "action": "get-interface", "index": 0 }
status Returns current tunnel information.	{"target": "tunnel", "action": "status" }
reset Performs a disconnect & reconnect.	{"target": "tunnel", "action": "reset" }

System Commands

shutdown Shuts down the client and terminates.	{ "target": "system", "action": "shutdown" }
set-log Enables logging to file or changes output file. Parameters file The filename that the log should be written to. Required. fileMode can be append or overwrite. Required.	{ "target": "system", "action": "set-log", "file": "/var/log/saneclient.log", "fileMode": "append" }
set-script-path Changes the directory that points towards the client scripts. (/opt/bondix/client/scripts by default) Parameters path Path to the new bondix script directory.	{ "target": "system", "action": "set-script-path", "path": "/etc/bondix/scripts" }
set-webinterface Enables the integrated webserver & debug webinterface. Parameters host IP that the service should listen on. Required. port TCP Port that the service should listen on. Required. allowConfig En- or disables web configuration. Not required, enabled by default. allowMonitor En- or disables web monitor. Not required, enabled by default. configApiKey The password required to access the realtime monitor monitor. webroot Web root directory. Points to the "www" subdirectory in installation directory. Not required, changing not advised.	{ "target": "system", "action": "set-webinterface", "host": "0.0.0.0", "port": "80", "allowConfig": false, "allowMonitor": true, "configApiKey": "123456", "webroot": "/tmp/" }